QUANTEC® SE-509 is a specific formula to be used in concrete mixes which have very low water content, and where accuracy and consistency in the manufacturing process are required with excellent dimensional stability, surface finish and normal structure.
QUANTEC® SE-509 is based on a blend of carboxylated polyethers and synthetic surfactants, for use in block mix concretes, and low slump concrete systems involving vibro-compression and instant demoulding.
QUANTEC® SE-509 increases mixture performances without cohesion losses, providing full cement hydration and strength development. The use of admixture can represent up to 20% strength increase at the same cement content.
| Appearance | Amber Liquid |
| Specific Gravity (20°C) | 1.05 |
| Alkali Content (eq.Na2O) | 0.50% |
| Chloride Content | Minimal in semi-dry |
| Air Entrainment | 1.0% |
| Freezing Point | 0ºC |
QUANTEC® SE-509 is supplied ready for use.
QUANTEC® SE-509 should be added in its supplied form with the batching water, after the addition of the cement.
QUANTEC® SE-509 may be used in all zero or low slump concretes, including extruded concrete, where improved compaction and reduced efflorescence are beneficial.
QUANTEC® SE-509 can be used with all types of Portland cement, including cement replacement materials.
For use with special cements we recommend that you consult GCP Applied Technologies.
QUANTEC® SE-509 should not under any circumstances be premixed with other admixtures. The performance of the product will be affected by the presence of other chemical admixtures.
We recommend that all admixtures be added separately into the mix.
The effect of overdosing QUANTEC® SE-509 is a function of the degree of overdose.
Overdosing in semi-dry mixes will yield a more plastic mixture, and problems may be experienced with edge slumping of cast masonry units. A reduction in compressive strength may also be noticed.
Any situation where an overdose is suspected, careful inspection of the concrete in its plastic state should be conducted. Particular attention to consistency and cohesiveness prior to a decision on the suitability of the concrete for the particular application in question.
| Range | 400 ml -700 ml per 100 kg cement |
| 0.40% -0.70% (v/w) by wt. of cement | |
| As a guide to trials an addition rate of 0.50-0.60% volume by weight of cement is suggested. | |
| For advice and assistance with trials we recommend that you consult GCP Applied Technologies. | |
QUANTEC® SE-509 is best assessed after preliminary tests in process using the actual mix constituents to determine the optimum dosage.
It is preferable that the QUANTEC® SE-509 should be introduced into the mixer by means of automatic dispensing equipment.
Equipment or advice on dispensing can be obtained from GCP
For further information on Health and Safety matters regarding this product we recommend that you consult the relevant Material Safety Data Sheet from GCP.
In line with general chemical handling precautions avoid contact with skin or eyes and protective gloves/goggles should be worn.
QUANTEC® SE-509 is supplied in 15 and 205 non returnable drums and 1,000 litre totes.
Alternatively, bulk deliveries can be arranged.
QUANTEC® SE-509 should be stored away from extremes of temperature and then protected from frost. The product should be kept out of direct sunlight in shaded storage at all times.
12 months from date of manufacture.
12 months from date of delivery.
Our Technical Service department of GCP Applied Technologies is available to assist you in the correct use of our performance chemicals.
We hope the information here will be helpful. It is based on data and knowledge considered to be true and accurate, and is offered for consideration, investigation and verification by the user, but we do not warrant the results to be obtained. Please read all statements, recommendations, and suggestions in conjunction with our conditions of sale, which apply to all goods supplied by us. No statement, recommendation, or suggestion is intended for any use that would infringe any patent, copyright, or other third party right.
QUANTEC is a trademark, which may be registered in the United States and/or other countries, of GCP Applied Technologies Inc. This trademark list has been compiled using available published information as of the publication date and may not accurately reflect current trademark ownership or status.
© Copyright 2020 GCP Applied Technologies Inc. All rights reserved.
GCP Applied Technologies (UK) Ltd, Gate St, Dukinfield SK16 4RU.
This document is only current as of the last updated date stated below and is valid only for use in the United Kingdom. It is important that you always refer to the currently available information at the URL below to provide the most current product information at the time of use. Additional literature such as Contractor Manuals, Technical Bulletins, Detail Drawings and detailing recommendations and other relevant documents are also available on www.gcpat.uk. Information found on other websites must not be relied upon, as they may not be up-to-date or applicable to the conditions in your location and we do not accept any responsibility for their content. If there are any conflicts or if you need more information, please contact GCP Customer Service.
Last Updated: 2023-06-13
https://gcpat.uk/en-gb/solutions/products/quantec-se-509